Page 2 - MPD - MH200RW Datasheet
P. 2



Model Selection Guide www.micropowerdirect.com
Input Output
Model Capacitive Effi ciency Fuse Rating
Number Voltage (VDC) Current (mA) Voltage Current Current Load (%, Typ) Slow-Blow
Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (µF Max) (mA)
MH205S-03RW 5 4.5 - 10.0 334 40 3.3 400.0 0.0 100 79 1,000
MH205S-05RW 5 4.5 - 10.0 494 40 5.0 400.0 0.0 100 81 1,000
MH205S-12RW 5 4.5 - 10.0 472 40 12.0 167.0 0.0 100 85 1,000
MH205S-15RW 5 4.5 - 10.0 462 40 15.0 134.0 0.0 100 87 1,000
MH205D-05RW 5 4.5 - 10.0 482 40 ±5.0 ±200.0 0.0 100 83 1,000
MH205D-12RW 5 4.5 - 10.0 469 40 ±12.0 ±83.0 0.0 100 85 1,000
MH205D-15RW 5 4.5 - 10.0 473 40 ±15.0 ±67.0 0.0 100 85 1,000
MH212S-03RW 12 9.0 - 18.0 138 27 3.3 400.0 0.0 100 80 600
MH212S-05RW 12 9.0 - 18.0 201 27 5.0 400.0 0.0 100 83 600
MH212S-12RW 12 9.0 - 18.0 192 27 12.0 167.0 0.0 100 87 600
MH212S-15RW 12 9.0 - 18.0 193 27 15.0 134.0 0.0 100 87 600
MH212D-05RW 12 9.0 - 18.0 198 27 ±5.0 ±200.0 0.0 100 84 600
MH212D-12RW 12 9.0 - 18.0 193 27 ±12.0 ±83.0 0.0 100 86 600
MH212D-15RW 12 9.0 - 18.0 195 27 ±15.0 ±67.0 0.0 100 86 600
MH224S-03RW 24 18.0 - 36.0 70 15 3.3 400.0 0.0 100 79 300
MH224S-05RW 24 18.0 - 36.0 99 15 5.0 400.0 0.0 100 84 300
MH224S-12RW 24 18.0 - 36.0 97 15 12.0 167.0 0.0 100 86 300
MH224S-15RW 24 18.0 - 36.0 96 15 15.0 134.0 0.0 100 87 300
MH224D-05RW 24 18.0 - 36.0 99 15 ±5.0 ±200.0 0.0 100 84 300
MH224D-12RW 24 18.0 - 36.0 97 15 ±12.0 ±83.0 0.0 100 86 300
MH224D-15RW 24 18.0 - 36.0 97 15 ±15.0 ±67.0 0.0 100 86 300
MH248S-03RW 48 36.0 - 75.0 35 8 3.3 400.0 0.0 100 79 200
MH248S-05RW 48 36.0 - 75.0 50 8 5.0 400.0 0.0 100 83 200
MH248S-12RW 48 36.0 - 75.0 49 8 12.0 167.0 0.0 100 85 200
MH248S-15RW 48 36.0 - 75.0 49 8 15.0 134.0 0.0 100 86 200
MH248D-05RW 48 36.0 - 75.0 51 8 ±5.0 ±200.0 0.0 100 82 200
MH248D-12RW 48 36.0 - 75.0 49 8 ±12.0 ±83.0 0.0 100 84 200
MH248D-15RW 48 36.0 - 75.0 50 8 ±15.0 ±67.0 0.0 100 84 200
Notes:
1. The specifi ed maximum capacitive load is for each output. A 3W version of this module is also available
2. Cross regulation is measured with the main output set at 100% load. The second output is For more information see the MH300RW series datasheet.
varied from 75% to 100% load.
3. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor Or call the factory at 781-344-8226
is connected from the +VOUT to the -VOUT pins. If the application is noise sensitive; connecting
a low ESR 3.3 µF capcitor should be used. This capacitor should be mounted as close to the Mechanical Dimensions
converter as possible.
4. Transient recovery is measured to within a 1% error band for a load step change of
25%.
5. Output overload protection is provided by a fold back current limiting circuit with
auto-recovery. A long-term overload could damage the unit.
6. To meet the specifi ed EN 61000-4-4 and EN 61000-4-5 limits, an external
capacitor must be connected across the input pins of the module. A 220 µF/100V
capacitor is recommended. This capacitor should be mounted as close to the module as
possible.
7. Operation at no load will not damage these units.
8. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.


Derating Curve




Pin Con nec tions
Pin Single Pin Dual
1-V 1-VIN
IN
4+VIN 4+VIN
5+VOUT 5+VOUT
6 No Pin 6 Common
7-V 7-VOUT
OUT



MicroPower Direct Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.5)
We Power Your Success - For Less! • Pin 1 is marked by a “dot” or indentation on the unit
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2