Page 2 - MPD MG200xxEI Datasheet
P. 2



Model Selection Guide www.micropowerdirect.com
Output
Input Output Load Capacitive
Model Regulation Load Effi ciency Fuse Rating
Number Voltage (VDC) Current (mA) Voltage Current Current (µF Max) (%, Typ) Slow-Blow
(mA)
Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) % Typ.
MG205S-05EI 5 4.5 - 5.5 500 25 5.0 400 40.0 12.0 220 80 1,000
MG205S-12EI 5 4.5 - 5.5 476 25 12.0 167 17.0 8.0 220 84 1,000
MG205S-15EI 5 4.5 - 5.5 476 25 15.0 133 13.0 7.0 220 84 1,000
MG205D-05EI 5 4.5 - 5.5 500 25 ±5.0 ±200 ±20.0 12.0 100 80 1,000
MG205D-12EI 5 4.5 - 5.5 476 25 ±12.0 ±83 ±8.0 8.0 100 84 1,000
MG205D-15EI 5 4.5 - 5.5 476 25 ±15.0 ±67 ±7.0 7.0 100 84 1,000
MG212S-05EI 12 10.8 - 13.2 205 15 5.0 400 40.0 12.0 220 81 500
MG212S-15EI 12 10.8 - 13.2 198 15 15.0 133 13.0 7.0 220 84 500
MG212D-15EI 12 10.8 - 13.2 198 15 ±15.0 ±67 ±7.0 7.0 100 84 500
MG215D-15EI 15 13.5 - 16.5 157 10 ±15.0 ±67 ±7.0 7.0 100 85 300
MG224S-05EI 24 21.6 - 26.4 101 8 5.0 400 40.0 12.0 220 82 250
MG224S-09EI 24 21.6 - 26.4 99 8 9.0 222 22.0 9.0 220 84 250
MG224S-15EI 24 21.6 - 26.4 99 8 15.0 133 13.0 7.0 220 84 250
MG224D-12EI 24 21.6 - 26.4 99 8 ±12.0 ±83 ±8.0 8.0 100 84 250
MG224D-15EI 24 21.6 - 26.4 99 8 ±15.0 ±67 ±7.0 7.0 100 84 250
Notes: Derating Curve
1. Output load regulation is specifi ed for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 1 µF ceramic capacitor & 10 µF electrolytic
capacitor be placed in parallel from the +Vout pin to the -Vout pin for single output models, or from each output
to common for dual output models.
3. Operation at no load will not damage these units, however, they may not meet all specifi cations.
4. These converters are specifi ed for operation without external components. However, in some applications the
addition of input/output capacitors will enhance stability and reduce output ripple. The simple connection shown
below will typically meet EN 55022 Class B. For dual output units, a capacitor should be connected from each
output to common.










VIN C1 C2 L1 VOUT C3 Mechanical Dimensions
5 VDC 4.7 µF/50V --- 6.8 µH 5 VDC 10 µF
12 VDC 2.2 µF/50V 470 pF/3 kV 6.8 µH 9 VDC 4.7 µF
15 VDC 2.2 µF/50V 470 pF/3 kV 6.8 µH 12 VDC 2.2 µF
24 VDC 1.0 µF/50V 470 pF/3 kV 6.8 µH 15 VDC 1.0 µF
±5 VDC 4.7 µF
±12 VDC 1.0 µF
±15 VDC 0.47 µF
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.





Pin Connections
Pin Single Dual Pin Single Dual
IN
1-V -VIN 9 No Pin Common
7NC NC 10-V -VOUT
OUT
8+VOUT +VOUT 14 +VIN +VIN
NC = No Connection

MicroPower Direct Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
We Power Your Success - For Less! • Pin 1 is marked by a “dot” or indentation on the unit
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2