Page 2 - MPD MG200xxE Datasheet
P. 2



www.micropowerdirect.comww.micropowerdirect.comwww.micropowerdirect.com
Model Selection Guide w
Input Output Load Output
Model Regulation Capacitive Effi ciency Fuse Rating
Load
Number Voltage (VDC) Current (mA) Voltage Current Current (µF Max) (%, Typ) Slow-Blow
Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) % Typ. (mA)
MG203S-05E 3.3 2.97 - 3.63 757 40 5.0 400 40.0 12.0 220 80 1,500
MG205S-05E 5 4.5 - 5.5 500 25 5.0 400 40.0 12.0 220 80 1,000
MG205S-12E 5 4.5 - 5.5 476 25 12.0 167 17.0 8.0 220 84 1,000
MG205S-15E 5 4.5 - 5.5 476 25 15.0 133 13.0 7.0 220 84 1,000
MG205D-05E 5 4.5 - 5.5 500 25 ±5.0 ±200 ±20.0 12.0 100 80 1,000
MG205D-09E 5 4.5 - 5.5 482 25 ±9.0 ±111 ±11.0 9.0 100 83 1,000
MG205D-12E 5 4.5 - 5.5 476 25 ±12.0 ±83 ±8.0 8.0 100 84 1,000
MG205D-15E 5 4.5 - 5.5 476 25 ±15.0 ±67 ±7.0 7.0 100 84 1,000
MG212S-05E 12 10.8 - 13.2 205 15 5.0 400 40.0 12.0 220 81 500
MG212S-12E 12 10.8 - 13.2 198 15 12.0 167 17.0 8.0 220 84 500
MG212S-24E 12 10.8 - 13.2 198 15 24.0 83 8.0 6.0 220 84 500
MG212D-05E 12 10.8 - 13.2 205 15 ±5.0 ±200 ±20.0 12.0 100 81 500
MG212D-09E 12 10.8 - 13.2 198 15 ±9.0 ±111 ±11.0 9.0 100 84 500
MG212D-12E 12 10.8 - 13.2 196 15 ±12.0 ±83 ±8.0 8.0 100 85 500
MG212D-15E 12 10.8 - 13.2 198 15 ±15.0 ±67 ±7.0 7.0 100 84 500
MG224S-05E 24 21.6 - 26.4 101 8 5.0 400 40.0 12.0 220 82 250
MG224S-09E 24 21.6 - 26.4 99 8 9.0 222 22.0 9.0 220 84 250
MG224S-12E 24 21.6 - 26.4 99 8 12.0 167 17.0 8.0 220 84 250
MG224D-05E 24 21.6 - 26.4 101 8 ±5.0 ±200 ±20.0 12.0 100 82 250
MG224D-09E 24 21.6 - 26.4 99 8 ±9.0 ±111 ±11.0 9.0 100 84 250
MG224D-15E 24 21.6 - 26.4 99 8 ±15.0 ±67 ±7.0 7.0 100 84 250
Notes: Derating Curve
1. Output load regulation is specifi ed for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 1 µF ceramic capacitor & 10 µF electrolytic
capacitor be placed in parallel from the +Vout pin to the -Vout pin for single output models, or from each output
to common for dual output models.
3. Operation at no load will not damage these units, however, they may not meet all specifi cations.
4. These converters are specifi ed for operation without external components. However, in some applications the
addition of input/output capacitors will enhance stability and reduce output ripple. The simple connection shown
below will typically meet EN 55022 Class B. For dual output units, a capacitor should be connected from each
output to common.








Mechanical Dimensions
VIN C1 L1 VOUT C2
3.3 VDC 4.7 µF/50V 6.8 µH 5 VDC 10 µF
5 VDC 4.7 µF/50V 6.8 µH 9 VDC 4.7 µF
12 VDC 2.2 µF/50V 6.8 µH 12 VDC 2.2 µF
24 VDC 1.0 µF/50V 6.8 µH 15 VDC 1.0 µF
24 VDC 1.0 µF
±5 VDC 4.7 µF
±7 VDC 2.2 µF
±9 VDC 2.2 µF
±12 VDC 1.0 µF
±15 VDC 0.47 µF
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Pin Connections
Pin Single Dual Pin Single Dual
1-V -VIN 9+VOUT +VOUT
IN
7 NC NC 11 No Pin -VOUT
8-VOUT Common 14 +VIN +VIN
NC = No Connection
MicroPower Direct Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
We Power Your Success - For Less! • Pin 1 is marked by a “dot” or indentation on the unit
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2