Page 2 - MPD - MG200MHI Datasheet
P. 2



Model Selection Guide www.micropowerdirect.com
Input Output Capacitive Load Fuse Rating
Model Effi ciency
Number Voltage (VDC) Current (mA) Voltage Current Current Load Regulation (%, Typ) Slow-Blow
Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (µF, Max) (%, Max) (mA)
MG205MS-05HI 5 4.5 - 5.5 606 60 5.0 400.0 8.0 330 12 66 1,200
MG205MS-12HI 5 4.5 - 5.5 600 60 12.0 165.0 3.0 330 10 66 1,200
MG205MS-15HI 5 4.5 - 5.5 605 60 15.0 133.0 2.5 330 10 66 1,200
MG205MD-12HI 5 4.5 - 5.5 553 60 ±12.0 ±83.0 ±1.5 100 10 72 1,200
MG205MD-15HI 5 4.5 - 5.5 542 60 ±15.0 ±66.0 ±1.0 100 10 73 1,200
MG212MS-05HI 12 10.8 - 13.2 253 30 5.0 400.0 8.0 330 12 66 500
MG212MS-12HI 12 10.8 - 13.2 250 30 12.0 165.0 3.0 330 10 66 500
MG212MS-15HI 12 10.8 - 13.2 252 30 15.0 133.0 2.5 330 10 66 500
MG212MD-12HI 12 10.8 - 13.2 224 30 ±12.0 ±83.0 ±1.5 100 10 74 500
MG212MD-15HI 12 10.8 - 13.2 220 30 ±15.0 ±66.0 ±1.0 100 10 75 500
MG224MS-05HI 24 21.6 - 26.4 126 15 5.0 400.0 8.0 330 12 66 250
MG224MS-12HI 24 21.6 - 26.4 125 15 12.0 165.0 3.0 330 10 66 250
MG224MS-15HI 24 21.6 - 26.4 126 15 15.0 133.0 2.5 330 10 66 250
MG224MD-12HI 24 21.6 - 26.4 112 15 ±12.0 ±83.0 ±1.5 100 10 74 250
MG224MD-15HI 24 21.6 - 26.4 110 15 ±15.0 ±66.0 ±1.0 100 10 75 250
Notes:
1. The specifi ed maximum capacitive load is for each output. Derating Curve
2. Load regulation is measured for a load change of 20% to 100%.
3. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor be
placed from the +VOUT pin to the -VOUT pin for single output units and from each output to common
for dual output units. For noise sensitive applications, the use of 3.3 µF capacitors will reduce the
output ripple.
4. Operation at no-load will not damage these units. However, they may not meet all specifi cations.
5. For dual output units, the maximum capacitive load is given for each output.
6. Dual output units may be connected to provide a 24 VDC or 30 VDC output. To do this, connect the
load across the positive (+VOUT) and negative (-VOUT) outputs and fl oat the output common.
7. The converter should be connected to a low ac-impedance source. An input source
with a highly inductive impedance may affect the stability of the converter. In applica-
tions where the converter output loading is high and input power is supplied over long
lines, it may be necessary to use a capacitor on the input to insure start-up. In this case,
it is recommended that a low ESR (ESR <1.0 at 100 kHz) capacitor be mounted close
to the converter. For 5V input units a 2.2 µF is recommended, for 12V input units, a
1.0 µF; and for 24V units a 0.47 µF.
8. It is recommended that a fuse be used on the input of a power supply for protection. See the
table above for the correct rating.
Mechanical Dimensions





Pin Connections
Pin Single Dual
1 -Vin -Vin
7NC NC
8 NC Common
9 +Vout +Vout
10 -Vout -Vout
16 +Vin +Vin
NC = No Connection














MicroPower Direct Mechanical Notes:
• All dimensions are typical in inch es (mm)
• Tolerance x.xx = ±0.01 (±0.25)
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2