Page 2 - MPD MPU-600CDx Datasheet
P. 2



Model Selection Guide www.micropowerdirect.com
Output Max.
Model Output Voltage Current With Output Regulation Ripple & Effi ciency
Noise
Number Factory 25 CFM Power (Note 3) (Note 2) (Note 6)
(Max A) (W)
V1 +5 VDC 50.00A
MPU-600CD-0512YYZ 600 ±5.0% 1.0% 80%
V2 +12 VDC 33.33A
V1 +5 VDC 50.00A
MPU-600CD-0524YYZ 600 ±5.0% 1.0% 80%
V2 +24 VDC 16.67A
V1 +12 VDC 33.33A
MPU-600CD-1224YYZ 600 ±5.0% 1.0% 80%
V2 +24 VDC 16.67A
Model Number
Some models may require a minimum order quantity.
Contact the factory for details at:
sales@micropowerdirect.com
Notes:
1. Output regulation includes line & load.
2. Ripple & noise is measured from 10 Hz to 20 MHz. Connection to the unit is made with a 0.1 µF
ceramic capacitor & a 22 µF electrolytic capacitor connected in parallel.
3. A 1% minimum load is required to maintain regulation & ripple specifi cations.
4. Transient recovery is measured to within a 1% error band for a load step change of 50% to 100%.
5. Isolation specifi cations are production HI-Pot tested for 3 seconds.
6. Effi ciency is measured with a 115 VAC input and full load.
7. Output power is given for the factory preset voltage. The maximum continuous output power level
is 600W with 25 CFM airfl ow. All models provide a peak power level of 900W for a maximum
duration of 500 µS. For more information, contact the factory.
8. Each unit includes an input fuse (250V/10A). Since this fuse is not fi eld replaceable, it is recom-
mended that an external fuse of the same size be used on the input of the power supply for
protection.
9. The Fan Drive output (at connector CN4) provides 12V/300 mA to drive an external fan.



Connections
Input Connector (CN1): Output Connector (CN2):
• Terminal Block: • Terminal Block:
Howder HD-121-3P: M3.5 Screws Howder HD-121-6P: M3.5 Screws Logic Signal Connector (CN3):
3 terminals, 9.5 mm Centers 6 terminals, 9.5 mm Centers • Mating Part No:
JST XHP-3 or equivalent
(CHYAO SHIUNN JS-1001-03)
Pin Function Pin Function
1 Field Ground 1 +V1OUT Pin Function
2 AC-Line 2 +V1OUT
1 Remote On/Off
3 AC Neutral 3+VOUT
2 Common
4-VOUT 3 Power Good
5 +V2OUT
Input Connector (CN1): 6 +V2OUT Interface Signals
• Molex Mating Part No:
Molex 09-50-3071 or equivalent Power Supply Bi-color LED Is green for “power on”;
(7 pins, 2 removed) On orange when protection enabled
Remote Sense Compensates for up to a 0.5V line drop
Pin Function Output Connector (CN2): Goes TTL high 100 to 500 mS after
• Molex Mating Part No:
1 Field Ground Power Good regulation. Goes low at least 1 mS
Molex 09-50-3141 or equivalent
2 Field Ground Signal before the loss of regulation. Will sink
3 Missing 100 mA.
4 AC-Line Pin Function
5 AC-Line 1 +V1OUT Remote On/Off A TTL low signal inhibits the output.
6 Missing 2 +V1OUT Hiccup mode.
7 AC-Neutral 3 +V1OUT
4 +V1OUT
Input Connector (CN1): 5 +V1OUT Fan Driver Connector (CN4):
• IEC320 or equivalent • Mating Part No:
6-VOUT
Available on “End Fan” models only JST XHP-2 or equivalent
7-VOUT
(CHYAO SHIUNN JS-2001-2)
8-VOUT
9-VOUT
10 -VOUT Pin Function
11 -VOUT 1 Minus
12 +V2OUT 2 Plus
13 +V2OUT
14 +V2OUT
MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2   3   4