Page 2 - MPD MPU-300 Datasheet
P. 2



www.micropowerdirect.comww.micropowerdirect.com.micropowerdirect.com
Model Selection Guide w www
Notes:
N
Output Voltage (VDC) Output Current (Max A) Ripple
Model Effi ciency 1. Output regulation includes line & load.
Number PreSet Range Convection With & Noise (%) 2. Ripple & noise is measured from 10 Hz to 20 MHz. Connection to the unit is made with a
0.1 µF ceramic capacitor & a 22 µF electrolytic capacitor connected in parallel.
25 CFM (% p-p)
3. A 1% minimum load is required to maintain regulation & ripple specifi cations.
MPU-300S-12YZ 12 VDC 12.0 - 13.8 12.50 25.00 ±1% 80% 4. Transient recovery is measured to within a 1% error band for a load step of 50% to 100%.
5. Isolation specifi cations are production HI-Pot tested for 3 seconds.
MPU-300S-15YZ 15 VDC 14.0 - 16.0 10.00 20.00 ±1% 80% 6. The full output range (see table) is covered in the safety agency certifi cation. Standard
models are factory set to the Preset voltage, but may be set to other levels within the range
MPU-300S-24YZ 24 VDC 23.0 - 28.0 6.25 12.50 ±1% 80% without affecting the agency certifi cation. For more information, contact the factory.
7. Output power is given for the factory preset voltage. The maximum continuous output
MPU-300S-48YZ 48 VDC 44.0 - 52.0 3.12 6.25 ±1% 80%
power level is 150W without providing 25 CFM airfl ow. All models provide a peak power
level of 600W for a maximum duration of 500 µS. For more information, contact the factory.
Model Number 8. Each unit includes an input fuse (350V/5A). Since this fuse is not fi eld replaceable, it is
recommended that an external fuse of the same size be used on the input of the power
supply for protection.
Models with other output voltage levels
are available (i.e. 5 VDC, 30 VDC, etc)
Contact the factory for details at:
sales@micropowerdirect.com
Mechanical Dimensions
Connections
Input Connector (CN1):
• Terminal Block:
Howder HD-601-3P
3 pins, 6.35 mm Centers
• Molex Mating Part No:
Molex 035977-0500 or equivalent
(two pins removed)
Pin Function
1 AC-Line
2 AC-Neutral
3 Field Ground
Output Connector (CN2):
• Terminal Block (Must be used on 12 VOUT):
Dinkle P-830N
M5 Screws
• Molex Mating Part No:
Molex 035977-0600 or equivalent
Pin Molex Pin Dinkle
1-V 1-VOUT
OUT
2-VOUT 2+VOUT
3-VOUT
4+VOUT
5+VOUT
6+VOUT
Logic Signal Connector (CN3):
• Mating Part No:
JST XHP-4 or equivalent
(CHYAO SHIUNN JS-21001-4)
• Mating Pins: JST SXH-002T-PO.6
U-Chassis Cover (C Suffi x) For AWG 30 to 26
Pin Function
1 Remote On/Off
2 Fan Fail
3 Common
4 Power Good
Fan Driver Connector (CN4):
• Mating Part No:
JST XHP-3 or equivalent
(CHYAO SHIUNN JS-21001-3)
3 Pins 0.98 Pitch
Pin Function
1 Fan Fail
2 Minus
3 Plus
MicroPower Direct Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2