Page 2 - MPD MPM-15S Datasheet
P. 2



Model Selection Guide www.micropowerdirect.com
Input Output Over Volt. Notes:
Model Effi ciency 1. Operation at no load will not damage the units, however, they may not meet
Number Current (A) Voltage Current (A) Protection (%, Typ) all specifi cations.
115 VAC 230 VAC (VDC) Max Min (VDC) 2. Load regulation is measured for an output change of 10% to 100% at nominal
input line.
MPM-15S-03 0.25 0.14 3.3 3.00 0.0 7.5 73 3. All units are rated for EN 55022 (CE/RE) class B without external components.
MPM-15S-05 0.25 0.14 5.0 2.80 0.0 7.5 76 4. All units are rated for EN 61000-4-4 (±2 kV) without external components. They
MPM-15S-09 0.25 0.14 9.0 1.60 0.0 12.0 78 will meet EN 61000-4-4 (±4 kV) with additional input fi ltering as shown below.
MPM-15S-12 0.25 0.14 12.0 1.25 0.0 20.0 80 5. All units are rated for EN 61000-4-5 (±1 kV/±2 kV) without external components.
They will meet EN 61000-4-5 (±2 kV/±4 kV) with additional input fi ltering as shown
MPM-15S-15 0.25 0.14 15.0 1.00 0.0 20.0 80
below.
MPM-15S-24 0.25 0.14 24.0 0.62 0.0 30.0 84 6. It is recommended that a fuse be used on the input of a power supply for protection.
MPM-15S-48 0.25 0.14 48.0 0.32 0.0 60.0 85 For the MPM-15S series, a 2.0A/250 VAC slow blow should be used.
Typical Connection The diagram below illustrates a typical application connection of the MPM-15S-xx series. Notes on this circuit (starting with the input circuit) are:
1. It is recommended that an external fuse and NTC be used. The recommended
fuse is a 3.15A/250V slow blow and for the NTC, a 5D-9.
2. An external MOV is required on the input to protect the unit in the event of
a surge. A 561KD14 or equivalent is recommended.
3. Recommended output fi ltering capacitors are:
C1 C2 TVS
MPM-15S-03 680 µF/16V 0.01 µF/25V SMBJ7.0A
MPM-15S-05 680 µF/16V 0.01 µF/25V SMBJ7.0A
MPM-15S-09 470 µF/25V 0.01 µF/25V SMBJ12A
MPM-15S-12 220 µF/25V 0.01 µF/25V SMBJ20A
MPM-15S-15 220 µF/25V 0.01 µF/25V SMBJ20A
MPM-15S-24 68 µF/25V 0.01 µF/25V SMBJ30A
MPM-15S-48 33 µF/25V 0.01 µF/25V SMBJ60A
Typical Connection: With ACFM-01 Input Module (See note 4)
Output capacitor (C2) is a high frequency, low resistance electrolytic capacitor.
Capacitor (C1) is ceramic. Voltage derating of capacitors should be >80%.
4. Input noise and surge suppression modules are available for a number of
MPD AC/DC power supplies. An MPM-15S-xx connection with the ACFM-01
is illustrated in the diagram at left. For pricing or full technical information on
these modules (ACFM-01 and ACFM-02) please contact the factory.
Pin Connections
Pin Function Pin Function
2 AC-Neutral 4 -Vout
3 AC-Line 8 +Vout

Derating Curve Mechanical Dimensions
















Input Voltage Vs Load















Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
MicroPower Direct The MPM-15-xx series is also available with
a chassis mount or DIN mount adapter.
Contact the factory for more information
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2