Page 2 - MPD MPM-15IS Datasheet
P. 2



Model Selection Guide www.micropowerdirect.com
Input Output 1 (Vout 1) Output 2 (Vout 2) Output 3 (Vout 3)
Capacitive
Model Current (A) Current (A) Current (A) Current (A) Effi ciency
Number Voltage Voltage Voltage Load (%, Typ)
115 VAC 230 VAC (VDC) Max. Min. (VDC) Max. Min. (VDC) Max. Min. (µF, Max)
MPM-15S-05IS 0.290 0.14 5.0 3.000 0.300 3,900 75
MPM-15S-12IS 0.275 0.14 12.0 1.250 0.125 2,200 79
MPM-15S-15IS 0.275 0.14 15.0 1.000 0.100 2,200 79
MPM-15S-24IS 0.275 0.14 24.0 0.625 0.063 2,200 79
MPM-15S-48IS 0.273 0.14 48.0 0.310 0.030 1,000 79
MPM-15D-12IS 0.275 0.14 +12.0 +0.625 +0.063 -12.0 -0.625 -0.063 ±1,500 79
MPM-15D-15IS 0.275 0.14 +15.0 +0.500 +0.050 -15.0 -0.500 -0.050 ±1,500 79
MPM-15T-0512IS 0.290 0.14 5.0 2.000 +0.200 +12.0 +0.200 +0.020 -12.0 -0.200 -0.020 Note 5 74
MPM-15T-0515IS 0.284 0.14 5.0 1.80 +0.200 +15.0 +0.150 +0.015 -15.0 -0.150 -0.015 Note 5 74
Other output combinations are available Derating Curve
Contact the factory for details at:
sales@micropowerdirect.com
Notes:
1. Load regulation is measured for an output change of 0% to 100% at nominal
input line. For multiple output models, the loads are balanced.
2. Operation at no-load will not damage these units. However, they may not
meet all specifi cations.
3. Output short circuit protection is provided by a “hiccup mode” circuit. The
unit recovers automatically when the fault condition is removed.
4. Output overload protection is provided by a fold back current limiting circuit.
5. For triple output models, the maximum capacitive load for the primary (5
VDC) output is 2,200 µF. For the auxilliary outputs it is ±1,500 µF.
6. The MPM-15IS series includes a built-in 2A/250 VAC fuse. It is recom-
mended that an external 1.5A slow blow fuse also be used on the input for
protection.



Model Number Mechanical Dimensions















Pin Connections
Pin Single Dual Triple
1 AC-Neutral AC-Neutral AC-Neutral
2 AC-Line AC-Line AC-Line
3NP NP -Vo 3
4 -Vo -Vo Common
5 NP Common +Vo 2
6 +Vo +Vo -Vo 1
7NP NP +Vo 1
NP = No Pin






Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct


We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2