Page 2 - MPD MPM-10EPB Datasheet
P. 2



Model Selection Guide www.micropowerdirect.com
Notes:
Input Output 1. Operation at no load will not damage the units, however, they may not
Model Standby Capacitive Effi ciency meet all specifi cations.
Number Current (A) Voltage Current Power Load (%, Typ) 2. Load regulation is measured for an output change of 10% to 100% at
(VDC) (A Max.) (W, Max) (µF Max.)
115 VAC 230 VAC nominal input line.
3. All units are rated for EN 55022 (CE/RE) class A without external components.
MPM-10S-03EPB 0.230 0.150 3.3 2.000 0.40 8,000 70
They will meet EN 55022 class B with additional input fi ltering as shown below.
MPM-10S-05EPB 0.230 0.150 5.0 2.000 0.40 8,000 74 4. All units are rated for EN 61000-4-4 (±2 kV) and EN 61000-4-5 (±1 kV) without
MPM-10S-09EPB 0.230 0.150 9.0 1.100 0.45 560 76 external components. They will meet EN 61000-4-4 (±4 kV), and EN 61000-4-5
(±2 kV/±4 kV) with additional input fi ltering as shown below.
MPM-10S-12EPB 0.230 0.150 12.0 0.900 0.40 1,200 76 5. It is recommended that a fuse be used on the input of a power supply for
protection. For the MPM-10S-xxEPB series, a 2.0A/250 VAC slow blow
MPM-10S-15EPB 0.230 0.150 15.0 0.700 0.50 1,000 78
should be used.
MPM-10S-24EPB 0.230 0.150 24.0 0.450 0.60 200 80
Typical Connection The diagram below illustrates a typical application connection of the MPM-10EPB series. Notes on this circuit (starting with the input circuit) are:
1. It is recommended that an external fuse and NTC be used. The recommended
fuse is a 2.0A/250V slow blow and for the NTC, a 5D-9.
2. An external MOV is required on the input to protect the unit in the event of a
surge. A 561KD14 or equivalent is recommended.
3. Recommended output fi ltering capacitors are:
C1 C2 TVS
MPM-10S-03EPB 1.0 µF/50V 220 µF/10V SMBJ7.0A
MPM-10S-05EPB 1.0 µF/50V 220 µF/10V SMBJ7.0A
MPM-10S-09EPB 1.0 µF/50V 120 µF/10V SMBJ12A
MPM-10S-12EPB 1.0 µF/50V 120 µF/25V SMBJ20A
MPM-10S-15EPB 1.0 µF/50V 120 µF/25V SMBJ20A
MPM-10S-24EPB 1.0 µF/50V 68 µF/35V SMBJ30A
Typical Connection: With ACFM-01 Input Module (See note 4)
The output fi ltering capacitor (C2) is a high frequency, low resistance electrolytic
capacitor. Capacitor (C1) is ceramic. Voltage derating of capacitors should be
80% or above.
4. Input noise and surge suppression modules are available for a number of MPD
AC/DC power supplies. An MPM-10S-xxEPB connection with the ACFM-01
is illustrated in the diagram at left. For pricing or full technical information on
these modules (ACFM-01 and ACFM-02) please contact the factory.
Pin Connections
Pin Function Pin Function
1 AC-Neutral 3 +Vo
Derating Curve
2 AC-Line 4 -Vo
Mechanical Dimensions













Input Voltage Vs Load
















Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
MicroPower Direct The MPM-10S-xxEPB series is also available
with a chassis mount or DIN mount adapter.
Contact the factory for more information
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
   1   2